Friday 27 February 2015

Efco Texture Mats

Well, rain stopped play yesterday, yet again, groan! The garden is officially a mud bath! Can't decide whether I should change tack and instead of building a shed open a spa offering mud facials, the Glastonbury experience (without the music that is), a World War I re-enactment opportunity, a pottery, a pig farm or a hippo sanctuary! lol


Thankfully my builders are a happy bunch and don't mind getting stuck in the mud...quite literally (they even had to dig the digger out!).

There has been a lot of interest in Efco's wonderful new Texture Mats. With them you can create fantastic pieces of jewellery with quite intricate polymer clay designs using the Sutton Slice technique - it's easy! 

Materials List
Cernit Clay (two colours)
Efco Texture Mat
Cernit Clay Knife Set
Cernit Roller or Pasta Machine (Optional)
Efco Jewellery Backing - Trapezoid Ring
Efco Ring Holder
Ceramic Tile
Swarovski Crystal



Step 1. Condition one of the colours of clay - whichever one you want to use as the foreground colour in your design ie. the one that will go into the Texture Mat. To make it easier to condition the clay, you can use a roller or pass the clay through a pasta machine several times. (Whatever tools you use with polymer clay eg. pasta machine, make sure you don't use them in food preparation afterwards - all tools used for clay should be kept for use with clay only.) 


Step 2. Take a lump of conditioned clay and push it into the mat. You need to cover an area larger than your chosen jewellery backing. Don't try and cover the whole area in one go and don't try to apply the clay too thinly because the clay is more likely to lift out of the mat crevices if you do. Better to apply it in thick chunks and spend more time removing the excess.


Step 3. Add more lumps of clay as necessary, until you have covered enough of the texture mat. Make sure to blend the sections of clay, working the joins until you can't see them. (If you can see the join on the top you will be able to see the join underneath which will show on your finished piece.)


Step 4. Make sure you have covered enough of the Texture Mat by checking against your finding. If you have just enough area covered for your finding with no excess you won't have enough covered because when you start removing the excess clay the edges will become ragged and unusable.


Step 5. Start shaving off the excess clay using the flexible Cernit knife. Always work out towards the edges of the clay. Try to keep the knife as flat as possible so that the back of the knife pushes the remaining clay into the mat whilst removing a slice. Don't try and remove it all in one go as you are more likely to remove all the clay not just the excess.


Step 6. Continue removing slices of clay until you can see the raised pattern of the Texture Mat.


Step 7. If you find some clay comes out of an area don't try and refill that one hole. Instead add a lump of clay pushing it into the mat before slicing off the excess.


Step 8. Make sure you can see the red raised areas of the Texture Mat, if not your finished design will not be quite so sharp.


Step 9. Take the second clay colour and work it until it is conditioned.


Step 10. Push the conditioned clay into the jewellery backing. 


Step 11. Remove the excess clay using the stiff Cernit blade. Hold it as flat as possible and, starting at the centre, cut across the finding (making sure the blade spans across both sides of the finding). Turn the finding around and remove the remaining excess clay by slicing the other way.


Step 12. Use your finger to smooth out the clay in the finding, making sure that it fills the recess right up to the edges.


Step 13. Flip the finding over and press it onto the clay covered area of the Texture Mat.


Step 14. Flip the mat over with the ring still attached and press on the back of the mat to make sure all the sections of clay have bonded. Then carefully flex the mat around every edge of the finding to check that all the sections that overlap the edges are stuck to the clay in the finding rather than still in the mat. 


Step 15. Slowly peel back the mat checking that all the clay from the mat is stuck to the clay in the finding.


Step 16. Gently press the raised surface of the clay to make sure it is completely adhered to the backing clay.


Step 17. Use the stiff Cernit blade to trim the excess clay from the edges of the finding. (Cut downwards as if trimming the edges of a pie to prevent distortion of the clay.) n.b. The trimmed bits of clay could be a combination of the two colours so don't combine it with the rest of your excess clay if you want to keep your colours pure.


Step 18. Use a lump of the same coloured clay to remove the excess clay still in the Texture Mat. You will find it easier if you flex the mat as you do this. 


Step 19. If you want to add a Swarovski crystal or two, do so now. Position it where you want and then carefully push it into the clay.


Step 20. Bake the clay according to the manufacturer's instructions (~30 mins at 110-130ÂșC). If baking a ring, it is wise to use the Efco ring stand so that as the clay softens during baking the pattern does not distort. The clay will shrink very slightly as it bakes so, if the clay falls out of the finding once 'fired', use a little superglue to stick it back in. (n.b. Don't forget to wash your hands after working with polymer clay.)


If you use two colours that are tonally the same or are shades of the same colour you will end up with a subtle effect. If you use two colours that are strikingly different you will have a more stunning finish.

As you can see it is easy to create amazing polymer clay jewellery with Efco's Texture Mats!

Click here if you want to see all the designs available in the Efco polymer clay Texture Mat range.

Happy crafting! :) 



2 comments:

  1. Hello,
    I really like your works. One question : where can I buy these texture ?
    Thank you

    ReplyDelete
    Replies
    1. I hope you've managed to get your texture mats now Nathalie :)
      Do let me know if you have any problems with Berkhamsted Arts and Crafts, Blue Gallery or Femme2deco. Fee x

      Delete